How to Fix Haier Washer That Has No Hot or Cold Water

A Haier washer that’s not operating effectively can create a myriad of problems, especially when it’s not using hot or cold water. It’s not only frustrating to have to deal with dirty clothes, but it may cost a lot of money to have professionals come in to resolve the issue. Fortunately, many issues with hot and cold water in a Haier washer can be easily fixed by the home owner. In this article, we’ll examine the common reasons for a washer to have cold or hot water that isn’t working and offer step-by step instructions on how to resolve the issue. We will help you troubleshoot the thermostat as well as check the water supply. It can save you money by not needing to repair a washer that isn’t warm or cold.

Inlet Hoses and Screens

Haier washers are connected to the household water supply using fill hoses. These hoses typically measure 5 to 6 feet long and will usually include wire or plastic screen inserted into the end of the hose which is connected to the faucet. The screen stops particles from entering the water inlet valve, which is located on the back of your appliance. How to examine the screens and hoses on the Haier washing machine:

  1. This is a easy inspection, and you do not have to take apart the washer. First, make sure the hoses and faucets are in good condition.
  2. Shut off the taps then disconnect the fill lines from the inlet valve and inspect the screens. Get rid of any dirt or sediment you discover. To verify you have enough water pressure to fully fill your hoses, place the ends of the hose into a bucket or tub, then turn on the faucet.
  3. Make sure the hose’s screen is free of dirt or damage when you don’t have enough pressure.
  4. You will need replacement hoses and screens from Haier if you find any problems during these examinations.

Water Inlet Valve

The Water Inlet valve that is on your Haier washing machine provides cold and hot water to washing and rinse. Two solenoids regulate the inlets that supply cold and hot water. The valve can be controlled by a electronic control, the timer and water temperature cycle selector. The timer, electronic control, water temperature/cycle selector and water level/pressure switches regulate the valve. How to check the water inlet valve inside the Haier washing machine with the aid of a multi-meter

  1. Before you begin this inspection be sure your washer is disconnected from the power and water supply.
  2. To remove the valve for test, remove all or a portion of the Haier washer cabinet. You’ll find the valve in the middle of the hose connection.
  3. Examine The Haier washer’s valve to see if there is cracks, wear or damage. It has screens within it that might have built up dirt or debris, in this case, it must be cleaned with care. If the screens are damaged, you will need to replace the whole valve.
  4. The resistance of a functioning valve can differ between models. Read the instruction manual to learn what your reading should be. Set the probes on the terminals of the valve using the RX1 setting of your multimeter.
  5. If you don’t get an indicator of continuity, you’ll need an Haier replacement water inlet valve.

Lid Switch

The lid switch on the top-load Haier washing machine is a security device that is designed to stop the motor circuit from operating when the lid is not closed. On certain models the circuit for water inlet can also be controlled. If the lid switch fails on these modelsthe power cannot be supplied to the valve for water inlet. If you’ve found that the water inlet valve of your Haier washer isn’t receiving power, then look at the switch on the lid. How to test the switch that controls the lid on aHaier washer:

  1. Before beginning, verify that you have disconnected the plug on your Haier washing machine.
  2. To locate the switch, you will need to pull off the cabinet or top panel. Once you’ve found it, verify that the levers and actuators aren’t damaged or stuck and also that the switch is operated mechanically.
  3. If no issues are found above, then remove the switch to check it for continuity . Set your multimeter at Rx1.
  4. Click the button to turn on the switch. Then make use of the probes make contact with the terminals. The probes should contact the terminals with a pressure of zero to almost zero.
  5. If you get a different reading, then you’ll need a Haier replacement lid switch.

Selector Swap or Water Temperature Switch

The selector switch or water temperature switch, determines the water temperature to be utilized for the wash and rinse portions of the. The switch is able to provide power to the proper solenoids of the valve that opens the water. The temperature selector switch may be the problem in the case that there is no power to the solenoids on the valve to open the water. How to test aHaier washing-machine selector switch using a multimeter:

  1. You will need to unplug the Haier washer first before you can begin testing and remove electrical components.
  2. Take the selector switch off your appliance . To test it, you will be required to remove the entire or a portion of your washer’s cabinet to access it. It’s typically attached to the frame of the Haier washer machine.
  3. It is your job to test the switches’ buttons one at each time. Begin by placing probes on the terminals of one button. The reading should read infinity. Then push the button to shift the reading to zero. Then press the button to switch the reading back into zero.
  4. If the readings you receive are different than those described in the previous paragraph, you’ll need a Haier replacement selector switch.

Water Level Pressure Switch

The water level switch is a switch that operates under pressure that is part of the water inlet valve circuit. This part is normally located behind the control panel and may be fitted with a hose or an air dome tube that connects it to the tub. This switch can be found beneath the tub in Haier washers equipped with electronic controls. If the switch is damaged, it may not supply power to the valve for water inlet. How to test the water level switch of a Haier washing machine

  1. Before you start, unplug the power source from the Haier appliance.
  2. A defective air dome or switch may cause the same issues as a malfunctioning switch. The cabinet of your washer should be opened to locate the issue and then remove the air dome hose. Cover one end with a seal and blow the other while it’s submerged in the water. No bubbles should be evident.
  3. To examine the appliance for signs of wear, cracking and damage or other issues Remove the switch. It is likely to be in the sump area under the tub or in the area behind your control panel.
  4. You may require a replacement water level switch from Haier in the event that you find any problems while conducting the checks.

Electronic Control

The electronic controller or timer can be used to regulate the moment when the valve to let water into the system gets electricity. The mechanical timer is comprised of several electrical contacts that are operated by a small motor as well as cams. These contacts supply power to the water inlet valve circuit throughout the fill, rinse and rinse portions of the cycle. How to check the timer controls of theHaier washer machine using a multimeter:

  1. To find the timer, disconnect your Haier washer and remove its control panel as well as the rear panel.
  2. Remove the timer from the Haier washer. Don’t pull the wires directly, instead, pull on the connectors.
  3. Set the multi-meter’s setting to Rx1 and, while pressing in on the button (if appropriate) connect the probes to the terminals that are connected to the motor (refer to the wiring diagram). You’re testing for continuity. You should see a reading of zero or nearly zero.
  4. You’ll need a new Haier timer If your test results differ. In the end the conclusion is that an Haier washer that does not have hot or cold water could be a difficult issue to address, however, it’s typically a simple fix.

There are many ways to troubleshoot common issues like clogged pipes, faulty valves and improper water temperature settings by following the instructions in this article. Be sure to unplug your Haier washer before you attempt repairs. If you’re uncertain about any part of the process then consult the manufacturer’s manual or consult a professional assistance. You can fix your Haier washer working again quickly and efficiently with a little patience and time. This will spare you the trouble of washing your clothes as well as the expense of repair.