How To Fix Maytag Washer That Fills and Drains At The Same Time

How To Fix Maytag Washer That Fills and Drains At The Same Time

If you’ve found yourself looking for the reason what’s going on with your Maytag washing machine is draining and filling at the same time, you’re not alone. This is a frequent issue that is caused by several problems. This article will discuss the most frequent causes, as well as offering step-by step instructions on fixing the problem with a Maytag washing machine that is able to drain and fill at the same time. It doesn’t matter if you’re an expert DIYer or are a novice fixer-upper, this tutorial will help you get your Maytag washing machine back in running order in a matter of minutes.

Water Inlet Valve: The water inlet valve of your Maytag washing machines can be used to fill tubs with cold, hot or warm water. The solenoids of the electric motor regulate the valve. They are controlled by the electronic control board, the timer and the water level control/water selector switch as well as the pressure switch. If your Maytag washer does not stop filling when draining the water inlet valve could be at fault. To verify that the valve is defective disconnect the washer as you notice the problem. The inlet valve may be defective if the washer fills continually. It could be due to the circuit controlling the valve. How to test the valve that opens water for theMaytag washing machine using a multimeter:

  1. Connect the water supply and the power source of your Maytag washer before beginning.
  2. The valve must be removed in order to test it; it will be found behind the connections of the hose. It’s necessary to disassemble any or all of your cabinet for the washer in order to take it off.
  3. Inside the valve you will find screens that might have deposits of dirt or particles. You must clean up any debris or dirt you discover. The screens can’t be sold separately and will have to be replaced should they become damaged. It is also important to inspect the valve’s exterior to check for wear, damage or cracks.
  4. Refer to your owner’s manual to determine the resistance reading required for a valve that is functional varies between the various models of Maytag washer’s. When you’ve got the correct reading, set the multimeter’s Rx1 setting to be in contact with the terminals of your valve’s terminals. If the valve isn’t in continuity, it can be replaced with a Maytag replacement valve.

The water level switch, also known as a pressure switch and air dome tube: The water level switch, which is activated by pressure from water, is used to set the level of water within the tub. The switch is usually located in the back of the control panel. It will include a hose or a dome tube connecting it to the tub. For Maytag washers with electronic controls it is possible that this switch will be situated in the bottom of the sump, beneath the tub. The water will then fill the tub and pressurize the air inside, pressing against the diaphragm. The switch will control the water inlet valve and close the valve when it reaches the right level of water. How to check the water level in aMaytag washer machine:

  1. Because you’ll work with electrical components, verify that you’ve disconnected your appliance prior to starting.
  2. Start by opening the Maytag washer’s cabinet and taking out the air dome. Set the hose in the water to seal one end and then blow it into the other. It is necessary to replace the air dome hose when bubbles appear.
  3. Examine the switch and hose for any signs of fraying, cracking wear, or damage. 4. If you notice that your switch is broken, you need a Maytag replacement water level switch. A Maytag washer that drains at the same time can be frustrating. However, with the proper tools and information, the problem is easily fixed.

When you are able to identify the most common causes, such as a clogged drain hose, a malfunctioning water intake valve or an inoperable pressure switch, you’ll solve the issue and get your Maytag washer back to working order in no time. For more information, make sure you refer to the Maytag washer’s owner’s guide. Also, unplug your appliance prior to making any repairs. It is possible to get your Maytag washer working like new with just a bit of patience and knowledge.