Hoover Washer Stops Mid Cycle – Solution

A washing machine is an essential appliance that is used in every home. It saves us time and energy by automating the process of washing clothes. However, a common problem that many individuals face is that their Hoover washing machine is stopped mid-cycle and leaves the clothes half-washed and a machine that is unable to complete the task. There are a variety of reasons the machine may stop mid-cycle, including issues with the drain system, power supply or even malfunctioning parts. This article will examine the most frequently-cited reasons why for a washer to stop working and offer solutions to resolve the issue.

Problem with Power coming in

Make sure the power cord is tightened. In order to ensure uninterrupted electrical power, it must be securely connected.

Hoover Washing Machine Control Board

Because a Hoover washer control board provides the necessary voltage to all of the washer’s electrical parts A malfunctioning board can cause the washing machine to stop mid-cycle. You can examine the board for indications of burning or a component that is shorted-out. After reviewing the wiring diagram it is possible to use a multimeter on the board to test the power output terminals.

Hoover Washing Machine Door Lock Motor and Switch Assembly

The door lock is used to secure the Hoover door of the washer while it is in operation. The washer will be operational when the door is closed. The door switch will stop the machine from functioning when the door of the washer isn’t shut. If the door lock is not working properly, the washing machine may stop mid-cycle. Door locks can either fail mechanically or electronically. Examine the door lock for any damage. Replace the door lock if it is broken or doesn’t latch correctly. To check if the door lock has failed electrically look up the diagram of your washer and use a multimeter test all the switches to the door lock for continuity. Replace the switch in the event that there is no continuity.

Hoover Washing Machine Lid Switch Assembly

The lid switch assembly blocks the Hoover washer from spinning while the lid is opened. The washer can stop in mid-cycle in the event that the lid switch is damaged. A multimeter is a good tool to examine every lid switch for continuity. If a lid switch is found to not have continuity, you should replace it.

Insufficient supply of water to Hoover

Check that the cold water is running into the tub. If the flow of cold water is slow or not entering the tub in any way It is possible that the Hoover washer will shut off ahead of the rinse, waiting for the tub to fill up. This could be due an inlet valve that is blocked, a partially closed main valve for water supply or low water pressure from your home.

Hoover Washing Machine Water Inlet Vave

During the rinse cycle the Hoover water inlet valve opens to allow water to enter the tub. If the valve to open the water inlet is damaged, the washer will keep waiting for water to flow into the washer, causing it to stop at the middle of the cycle. To determine if the water inlet valve is defective, make use of a multimeter and test the valve for continuity. Replace the valve for water inlet when it is not in continuity.

Hoover Washing Machine Drain Pump

The Hoover washing machine drain pumps assists in draining tub’s water by forcing it through a drain tube or pipe to drain the water. Since water may be drained from the tub numerous times during a wash cycle, a defective drain pump can stop the washing machine mid-cycle. Check the drain pump for obstructions in the event that there is water in the tub after the washer has stopped. To check for electrical continuity using the multimeter. This will allow you to determine whether the pump functions.

Hoover Washing Machine Main Control Board

The Hoover main control board might be inoperable. But, the control board itself is rarely the cause of this issue. Before replacing the main control board , be sure that you inspect the other parts that are more typically in need of repair.

Hoover Washing machine timer

The timer could be defective. It is often misdiagnosed. Before changing the timer, first check all of the more commonly defective parts. Check the wiring diagram of your washer to determine if the washer is in a state of deficiency. Then, use a multimeter for continuity test.

In the end it is clear that a Hoover washer that stops mid-cycle could be frustrating, but there are several methods to fix the issue. By following the steps outlined in this post, you will be able to pinpoint and solve the root reason for the problem such as a blocked drain, damaged motor or an electrical problem. Before you start any repairs, disconnect the machine. It is best to seek out professional assistance if you’re unsure of your ability to fix the problem. It’s possible to fix your Hoover washer machine with some perseverance, knowledge, and expertise. This will ensure that your clothes remain clean and fresh each time.