How To Fix Whirlpool Washer That Won’t Stop Filling With Water

Perhaps you’ve experienced the frustration of a Whirlpool washing machine that would not stop from filling up with water. It’s not just a waste of water and energy, but it can could also damage your floors as well as Whirlpool washer. We’ll address common issues and provide step-by-step instructions to fix a Whirlpool washing machine that is constantly filled with water.

There’s all the details you require to repair the issue with your Whirlpool washer, regardless whether you’re a pro or a novice. Read on if you’re looking to repair the problem with your Whirlpool washer!


Water Inlet Valve:

The Water Inlet Valve of your Whirlpool washing machine is used to fill the tub with cold, hot or warm water. The solenoids in the electric circuit regulate the valve. They are controlled by the electronic control board, the timer, the water level control/water selector switch, or the pressure switch. The valve for water inlet could be the cause of your issue if your Whirlpool washer fills up continuously throughout the course of. If your Whirlpool washer is filling up it is likely that the valve for water inlet may be the cause. The valve that lets water into the washer could be malfunctioning if the washer fills constantly. The issue could be within the electrical circuit that controls the valve. How do you test the valve that opens water for the Whirlpool washing machine using a multimeter Like all tests, ensure that you have shut off the power source to the Whirlpool appliance prior to beginning.

  1. It will be conducting electrical tests on the components.
  2. Find and remove the valve that opens your water supply. It is located behind the connections to the hose. To get to it, you’ll need the panel on the back to be taken off.
  3. Examine the valve visually to check for indications of wear. It is necessary to replace the entire valve, especially if it has screens.
  4. Make use of a multimeter to contact the valve’s terminals ports with Rx1. You should receive a different reading for every model. Check the manual to determine what you should get.
  5. You’ll need to replace the Whirlpool valve for water inlet in the event that the valve is damaged or the test results do not align with the guidelines.


Level switch and pressure switch and air dome tube:

The water level switch, which is activated by pressure from the water, can be used to adjust the level of water within the tub. The control panel is likely to include this component. It is connected to the tub via an air dome tube. The switch is located beneath the tub in Whirlpool washers that have an electronic control. The water will be able to fill the tub and then compress the air inside, pressing against the diaphragm. The valve for water inlet is controlled by the switch that will shut off the valve when it reaches the proper level of water. The washer may overfill if the tube damaged or leaky. The switch could be damaged and result in the washer filling excessively. How do you check the level of water in the Whirlpool washer machine: You’ll be working with electrical components, so be sure that you disconnect the washing machine from the power source prior to beginning.

  1. For the removal and location of the water level switch as well as the air dome tube that is in the inside of your Whirlpool washer, you need to open the cabinet.
  2. After the air dome tube has been removed, put one end inside the tank, and blow it into the other. Hoses that are not damaged will not create bubbles.
  3. Examine the hose and valve for wear, cracks, or damage. If you notice any issues in the previous inspections it is possible that you require a Whirlpool replacement Water Level Switch. A washing machine from Whirlpool that isn’t filled with water could cause expensive and annoying issues. It is possible to save time and money by identifying the cause and taking the appropriate steps to fix the issue.


This article can help you repair the problem with your Whirlpool washer, regardless whether the issue is in the water level switch or with the valve for inlet. Before you begin any repairs you should read the manual for your washer. It’ll provide specific instructions for troubleshooting and security precautions. If you’re not sure if the issue can be resolved on your own, it’s recommended to call an expert to complete the repairs. With just a bit of knowledge and the correct approach, you can repair Whirlpool washers that aren’t filling up with water. After that, go back to washing.