Amana washers that do not move to the next cycle of laundry can cause frustration and confusion. The issue could result from a variety of reasons, from the simplest to more complex. In this article, we’ll explore some of the most frequently-cited reasons for why Amana washers don’t go on to the next cycle .
We will also offer step-by-step guidance on how to diagnose and fix the issue. This guide is written for newbies and experts. It will help you understand how to solve the issue and get your Amana washer back to normal order within the shortest amount of time. The reason why your Amana washer won’t move to the next cycle will depend on the kind of washer you have: A top-load Amana washing machine will not advance to the spin or drain cycle if a broken lid switch is telling the timer that it’s open.
An Amana washing machine that isn’t able to finish the cycle could also have a damaged timer or defective water-level pressure switch. A malfunctioning or damaged drain pump, or the shifter assembly of a top-load vertical Amana washer could cause it to stop mid-cycle. The washer could also stop mid-cycle in the event that it is sludge-laden.
An Amana front-load washer could stop due to a broken door lock on the washer, failure of the main controller board or a damaged motor control board. If the washer is aware of an issue, it will send a digital error code to the controller board. This may result in the cycle having to be stopped. These repairs may be able to solve your Amana Washer issue.
Replace the switch on the lid of the washer:
The lid switch in a top-load Amana washer has a safety switch that determines if the lid on the washer is shut. The lid must be closed when the basket spins. if the Amana washer isn’t aware that the lid has been opened the machine will not spin or drain after washing. Certain top-load Amana models require that the washer lid be closed prior to the time the drive motor is started. A lid that is open can stop some top load Amana washers from filling. If the switch on the lid doesn’t know if the lid is shut change the switch. Replace the Amana washer’s washer shifter assembly.
Replace the washer’s shifter assembly:
The shifter assembly-also called the actuator in a top-load washer is mounted to the lower part of the gear case. The shifter assembly’s motor shifts the drive system’s direction between spinning mode and the agitation mode. The position of the drive system is monitored by a sensor mounted within the shifter. The washing machine will cease the cycle if the sensor, motor or mechanical component of the assembly for the shifter fails and give an error code. Replace the entire shifter assembly if it fails.
Replace the Amana washer door lock assembly:
The door lock assembly on a front-load Amana washer has a safety switch that can tell if the door of the washer is closed along with a latch as well as a locking mechanism. The door will not lock should any of the components fail when it is opened. If one of the components fails when the door is closed, it won’t open. Replace the entire assembly in case any component fails.
Replace the Amana washer’s main control board: The main electronic control board, also called the mother board controls the timing and the execution of washer’s component functions. It regulates the fill valves along with the drive motor and the drain pump.
Replace the Amana washer timer:
The timer is also known as cycle selector, is the dial that can be used to regulate the cycles of a Amana washing-machine with mechanical controls. The timer lets the Amana washer run through its cycles, from initial filling until the final spin. If the timer does not move the washer through its cycles, replace it.
Replace or repair the Amana drain pump for the washer:
The drain pump is the one responsible for draining water out of the washer’s wash cycle. The bearing of the pump can become stuck and the seal may fail or the impeller blades could break. The belt that drives belt-driven pump can wear out, and the pulley may shear off. If the Amana washer is saturated with water and a sound, it could be an indication of a damaged pump. It is possible to repair the pump in some cases by clearing the debris out of it and replacing the seal or fixing wiring issues. If the pump cannot be repaired or rebuilt, you must replace it.
Replacing the Amana washer motor control board:
The motor control board is a control circuit inside a front-load Amana washer that’s usually in the bottom of the washer near the drive motor. It monitors and controls drive motor speed and direction for the tumble and spin actions throughout the cycle. If the motor doesn’t run the motor control board might require replacement.
Replace the Amana washer water-level pressure switch:
The water-level pressure switch is used to determine the level of water in the wash tub. The washer will not be able to fill properly if the pressure sensor has been damaged. It could not fill completely or overfill, even to the point that it is overflowing. Replace the pressure switch if the device fails to sense or regulate the water level of the washer.