How To Fix Hoover Washer That Won’t Stop Filling With Water

How To Fix Hoover Washer That Won’t Stop Filling With Water

If you’ve ever had the experience of facing a Hoover washing machine that doesn’t stop filling with water you’re aware of how annoying it could be. Not only does it waste the water and energy it could also cause damage to your floors as well as your Hoover washer itself. In this post, we’ll take a look at the most common causes of this problem and give step-by-step instructions on fixing a Hoover washing machine that will not stop filling with water. You can find all the information you need to repair the issue with your Hoover washer, regardless if you are a professional or a novice. So if you’re ready to fix that pesky Hoover washer, continue reading!

Water Inlet valve

The Water Inlet Valve that is on the inside of your Hoover washing machine allows you to fill the tub with hot, cold or warm water for wash and rinse cycles. The solenoids in the electric circuit control the valve. They are controlled by the electronic control board, the timer and the water control switch for water level or the pressure switch. The water inlet valve might be the source of the issue if the Hoover washer fills constantly during an entire cycle. If your Hoover washer continues to fill and fill, the water inlet valve could be at fault. The water inlet valve may be inoperable if the washing fills continually. If the washer doesn’t fill the problem could be related to the circuit electrical that is controlling the valve. How to test the water-inlet valve of theHoover washing machine using the multimeter:

  1. Similar to other tests ensure that you’ve removed the power source from your Hoover appliance before beginning, as you will be working with electrical components.
  2. Locate and remove your water inlet valve. It’s situated behind the connections for the hose. To open it, you will need the panel on the back to be removed.
  3. Examine the valve visually for any indications of wear or damage. The valve is fitted with screens within it, inspect these screens for any debris. be sure to do this with care because the screens are not replaceable and if damaged, it is necessary to replace the entire valve.
  4. Use a multimeter to touch the terminals of the valve’s ports by using Rx1. The value you’ll receive varies from model to model so consult the owner’s manual to find out what you should receive from your test.
  5. It is necessary to replace the Hoover water inlet valve when the valve is damaged or your test results do not align with the guidelines.

Water level switch & pressure switch & air dome tube

The water level switch, which is activated by water pressure is used to regulate the water level in the tub. The switch is usually located in the back of the control panel and will be fitted with a hose or an air dome tube which connects it to the tub. For Hoover washers that have electronic controls, this switch may be located at the sump area beneath the tub. The water will be able to fill the tub and compress the air inside, pressing against the diaphragm. The water inlet valve will be controlled by the switch, which shuts off the valve when it reaches the correct level of water. The washer can overfill if the tube damaged or leaky. If the switch is defective it could cause the machine to overfill. How do you check the level of water in a Hoover washer machine:

  1. Because you will be handling electrical components, ensure that you have disconnected the washer from its power source prior to beginning.
  2. Then, open your Hoover washer’s cabinet to locate and then remove the water level switch as well as the air dome tube. Once removed, plug into one of the ends of the tube immerse it in water and blow it into the other end. A hose that is not damaged will not contain any bubbles that come out of it.
  3. Examine the hose and valve for any indications of wear, cracks, or damage.
  4. If you find any problems after performing the tests above it is possible that you require a Hoover replacement water level switch.

In the end, a Hoover washing machine that doesn’t stop running out of water can be an annoying and expensive issue to tackle. But, by identifying the most common causes for this issue , and taking necessary steps to remedy the issue, you will save yourself time and money. The issue could be a water level switch that is not working or a blocked valve for the inlet The solutions provided in this article can assist you in getting the Hoover washing machine back in working order. Before you tackle any repairs It’s recommended to review the instruction manual of the washer. It will provide specific steps to troubleshoot and security measures. If you’re not confident in your ability to fix the issue yourself you should contact a professional to handle the repair. Overall, with a bit of knowledge and the right approach you can repair an issue with a Hoover washer that keeps refilling and you can be back at doing laundry in a breeze.