The washing machine is an indispensable appliance for every home. The process of washing can be automated, which can save both energy and time. A lot of people confront the issue that their washer stops mid-cycle. They are left with dirty clothes and a machine that’s not capable of completing the task. The washer may stop mid-cycle due to a variety of reasons, such as issues in the drain system, or the power supply. We will look at the most frequent reasons why that a washer might stop functioning and provide practical solutions to resolve the issue.
Problem with Power coming in
Make sure the power cord is securely plugged in. To ensure that you have constant power, it should be securely connected.
Whirlpool Washing Machine Control Board
The control board of the Whirlpool washing machine provides voltage to all of the electrical components in the washer. A damaged board could cause the washing machine to stop in the middle of the cycle. The board is able to be examined for evidence of burned or damaged components. After looking over the wiring diagram it is possible to use a multimeter on the board to examine the power output connections.
Whirlpool Washing Machine Door Lock Motor and Switch Assembly
The door lock secures the Whirlpool door to the washer during operation. The washer can begin operating when the door is closed. The door switch stops the washer from operating when the door of the washer isn’t shut. The washer may stop mid-way through the cycle when the lock on the door fails. Door locks may fail electronically or mechanically. Examine the door lock for any damages. Replace the door lock if it’s broken or isn’t latching correctly. Examine the diagram of your washer to find out if the door lock is malfunctioning electrically. Use an a multimeter equipped with continuity testing equipment to test every switch. Replace the switch if there’s no continuity.
Whirlpool Washing Machine Lid Switch
The lid switch assembly will stop the Whirlpool washer from spinning once the lid is open. The washer may stop mid-cycle when the lid switch assembly is damaged. A multimeter is a good tool to test every lid switch for continuity. Replace the lid switch that is not in continuity.
Insufficient supply of water to Whirlpool
Make sure that the cold water is flowing into the tub. The washer won’t begin the rinse process if the cold water supply is not flowing at a sufficient rate or is not able to reach the tub. This could be due to an inlet valve that is blocked or a partially shut main valve for water supply, or the water pressure is low at your home.
Whirlpool Washing Machine Vave for Water Inlet
The Whirlpool water intake valve is opened in the course of the rinse, allowing water to flow into your wash tub. The washer waits for water to get into the machine if the valve for water inlet is not working properly. Then, it will stop at the middle of the cycle. A multimeter is a tool to test for continuity in the valve for water inlet. Replace the valve for water inlet when it is not in continuity.
Whirlpool Washing Machine Pump for drain
The Whirlpool washing machine drain pump assists in draining the tub’s water by forcing it through pipes or drain tubes to let the water drain. A malfunctioning drain pump could cause the washer to stop in mid-cycle because water is removed several times from the tub during the wash cycle. Examine the drain pump for obstructions if you find water in the tub after the washing machine has stopped. To check for electrical continuity using the multimeter. This will allow you to determine if the pump is working.
Whirlpool Washing Machine Main Control Board
It could be that the primary control board at Whirlpool could be malfunctioning. This isn’t a typical issue. Before replacing the control board that is in charge, make sure you check all other components that are often damaged.
Whirlpool Washing machine timer
It’s possible that the timer could be malfunctioning. It’s easy to miss the mark on the problem with the timer. When replacing it, ensure that you test all parts which are likely to be in a state of deficiency. Examine the wiring diagram of the washer in order to identify if it’s damaged. Next, you can utilize a multimeter to conduct continuity checking.
A Whirlpool washing machine that stops midway through the cycle could be an annoyance. But, there are a variety of solutions to resolve the issue. Fix the issue by following the suggestions in this post. Before you begin any repairs, disconnect the device. It is recommended to seek professional assistance if you’re not sure of your ability to fix the issue. It’s possible to repair your Whirlpool washer with some patience, understanding and experience. This will make sure that your clothes are clean and fresh each time.