Kenmore Washer Stops Mid Cycle – Solution

A washing machine is an indispensable appliance for every home. It is a time-saver and energy by automating the process of washing clothes. A lot of people confront the issue of their washer not working properly. It leaves them with dirty clothes and a machine not ready to complete the job. There are a variety of reasons a washer may be stopped mid-cycle, such as issues with the water drainage system, the power supply or parts that are malfunctioning. In this article, we’ll examine the most common causes of this issue and offer practical solutions to help you solve the issue with your Kenmore washer so that you can be able to do the laundry you love with ease.

Problem with Incoming Power

Make sure that the power cord is not loose. To ensure constant electrical power, it should be securely plugged in.

Kenmore Washing Machine Control Board

The Kenmore washing machine control board supplies the necessary voltage to all of the washer’s electrical parts A malfunctioning board can cause the washing machine to stop mid-cycle. The board can be checked for signs of burnt or damaged components. You can also make use of a multimeter in order to examine the output power terminals on the board following a review of the wiring diagram of the appliance.

Kenmore Washing Machine Door Lock Motor and Switch Assembly

The door lock locks the Kenmore door of the washer while it is in operation. The washer will be operational after the door has been shut. If the door of the washer has not shut the door switch blocks the washer from working. The washer will be stopped halfway through the cycle in the event that the lock on the door fails. The door lock could fail mechanically or electrically. Examine the door lock for any damage. Replace the door lock if it’s broken or does not latch properly. Look over the diagram on your washer’s door to determine if the lock isn’t working electrically. You can then use a multimeter and continuity testing equipment to examine every switch. If one of the switches does not have continuity, then replace the switch.

Kenmore Washing Machine Lid Switch Assembly

The lid switch assembly stops the Kenmore washer spinning when the lid is opened. If the lid switch assembly fails, the washer may stop mid-cycle. To find out if the lid switch assembly is not functioning properly, use a multimeter to test every lid switch for continuity. Replace any lid switch that does not have continuity.

Insufficient supply of water to Kenmore

Make sure that the cold water supply is able to enter the tub. If the cold water supply is not flowing smoothly or does not enter the tub at all It is possible that the Kenmore washer will stop in the middle of the rinse cycle while waiting for the tub to fill. It could be due to a water inlet valve that has been blocked or a partially shut main valve for water supply, or low pressure water coming from your home.

Kenmore Washing Machine Water Inlet Vave

During the rinse process, during the rinse cycle, Kenmore water inlet valve opens to allow water to enter the wash tub. If the valve that allows water to enter the wash tub is damaged, the washer will keep waiting for water to get into the washer and then stop mid-cycle. To check if the inlet valve is damaged, you can use an instrument to check it for continuity. If the valve that is used to supply water doesn’t have continuity then replace it.

Kenmore Washing Machine Drain pump

A Kenmore drain pump for washing machines helps in the removal of water from the tub through forcing the water to go through a drain hose to a laundry tub or drain pipe. A malfunctioning drain pump can cause the washer to stop mid-cycle and water could be drained several times from the tub during a wash cycle. If you find that there is water in the tub even after the washing machine stops, examine the drain pump for any obstruction. You may also utilize a multimeter to check the drain pump to determine if it is in electrical continuity. verify if the pump can function or not.

Kenmore Washing Machine Main Control Board

It is possible that the main control board in Kenmore might be in a state of deficiency. However the main control board is usually not to blame for this condition. Before replacing the control board in the main take a look at all the components that are most likely to be defective.

Kenmore Washing machine timer

The timer might be defective. It is easy to misdiagnose the timer. Before replacing it, be sure you inspect all the components which are likely to be in a state of deficiency. Look over the wiring diagram of your washer to determine if it is malfunctioning. You can then use a multimeter for continuity testing.

A Kenmore washing machine that stops midway through the cycle could be an annoyance. But, there are a variety of solutions to resolve the issue. It is possible to fix the issue by following the suggestions in this article. Make sure you unplug your device and take the necessary safety precautions before attempting any repairs. It’s best to seek professional assistance if you’re unsure of your ability to fix the problem. With some patience and knowledge, you’ll make your Kenmore washing machine back up and running with ease, making sure your clothes come out fresh and clean every time.