You’ve probably experienced the frustration of an Speed Queen washing-machine that wouldn’t stop filling up with water. Not only does it waste the water and energy but it could also cause damage to your floors or your Speed Queen washing machine itself.
We’ll address common issues and provide step-by-step instructions to fix a Speed Queen washing machine that continues to fill up with water. It doesn’t matter if you’re an expert DIYer or an absolute novice, this article will provide the information you need to fix your Speed Queen washing machine back into running in good working order. Follow this article if you’re eager to repair your Speed Queen washer!
Water Inlet valve
The Water Inlet Valve located on your Speed Queen washing machine is used to fill the tub up with cold, warm or hot water for the wash and rinse cycles. The solenoids of the electric motor control the valve. They are controlled by the electronic control board, the timer, the water control switch for water level or the pressure switch. If your Speed Queen washer does not fill over the course of a cycle, the water inlet valve could be at fault. If the Speed Queen washer is filling up then the water inlet valve could be at fault. The water inlet valve could be malfunctioning if the washer fills continuously. The problem may be in the electrical circuit that controls the valve. How to test the valve that opens water for the Speed Queen washing-machine using the multimeter:
- Similar to other tests, ensure that you have removed the electrical source of your Speed Queen appliance before beginning since you’ll be working with electrical components.
- Find and remove your water inlet valve. It’s usually located just behind the hose connections and you’ll need remove the panel on the rear for access.
- Examine the valve visually to see if there are any signs of wear or damage. The valve comes with screens in it. Examine these screens for any debris, take care as the screens can’t be replaced If they are damaged, it is necessary to replace the entire valve.
- Utilizing a multimeter on Rx1, touch the probes to the valve’s connections. You should get a different reading for every model. Consult your manual to find out what you should get.
- If your valve is damaged or if your tests do not meet the results recommended it is recommended that you purchase Speed Queen replacement water inlet valve.
Water Level Switch and Pressure Switch & Air Dome Tube
The water level switch is a switch that activates by pressure that is used to determine the correct water level in the tub. The control panel is likely to contain this feature. It will be connected to the tub with the use of a hose or air dome tube. For Speed Queen washers, which have electronic controls the switch might be situated in the bottom of the sump, beneath the tub. The water will then fill the tub and then compress the air inside, pushing against the diaphragm. The water inlet valve will be operated by the switch, which will shut off the valve at the appropriate level of water. The washer could overfill if the tube damaged or leaky. The switch could be defective and cause the washer to fill excessively. How to check the water level switch of the Speed Queen washing machine
- Because you’ll be working with electrical components, be sure you have disconnected your washer from its power source before you begin.
- You must open your Speed Queen appliance’s cabinet to locate and take off the water level switch, as well as the air dome tube. When the air dome tube is removed, place one end in the tank, and blow into the other. An undamaged hose will not have any bubbles coming out of it.
- Check the valve and hose for wear, cracks or damage. If you observe any problems after the above inspections, you might need Speed Queen replacement Water Level Switch.
In the end, a Speed Queen washing machine that keeps running out of water can be an aggravating and costly issue to address. You can save time and money by discovering the reasons and then taking steps to correct the problem. It doesn’t matter if the issue is an issue with the water level switch or a clogged inlet valve.
The solutions provided in this article can help you get your Speed Queen washing machine to work properly. Before you tackle any repairs before you begin any repairs, check the manual for the washer. It’ll provide specific directions for troubleshooting as well as security measures. If you’re uncertain about your capability to fix the problem on your own, it’s best to call an expert to assist with the repair. Overall, with a few hours of research and the correct approach with the right approach, you can fix a Speed Queen washer that isn’t in its water-filled systole and get back to washing your laundry without difficulty.