How To Fix GE Washer That Fills and Drains At The Same Time

How To Fix GE Washer That Fills and Drains At The Same Time

There’s no one else than person who is wondering why your GE washer is draining at the same time. It’s a common issue and is caused by a variety of factors. In this article, we’ll discuss the most frequently-cited causes of this problem and give step-by-step directions for fixing the problem with a GE washing machine that fills and drains at the same time. No matter if you’re a skilled DIYer or just a newbie repairer, this guide will help you fix your GE washing machine back in running order in a matter of minutes.


Water Inlet Valve

The water valve that is in the inlet of your GE washing machines is used to refill the tubs with cold, hot or warm water. The valve is operated using electronic solenoids controlled by the timer or electronic control board as well as the water level control/water level selector switch, or the pressure switch. The valve that lets water into the water can be the issue if your GE washer is filled up during a drain cycle. To verify that the valve is in error disconnect the washer as the symptoms occur. If the GE washer does not stop filling, then the inlet valve is malfunctioning.

If the GE washer stops filling the water, then the issue may be related to the electrical circuit that regulates the valve. How do you test the water inlet valve on the GE washing machines by using a multimeter

  1. Before you start, disconnect the water supply and power source from the GE washer.
  2. For testing the valve, take it out. It is hidden behind the hose connections. To remove the valve, you will need to disassemble your washer’s cabinet.
  3. Inside the valve, you’ll find screens that might have accumulations of dirt or other dirt. Clean up anything you can find, but exercise cautiously as these screens cannot be purchased as an independent item from the valve. And in the event that they become damaged, you’ll need to replace the entire valve. It is also important to inspect the outside of the valve to check for wear, damage or cracking.
  4. Your owner’s manual will give the resistance readings needed for valves that are functional. They vary between GE washer models. When you’ve determined the resistance reading you should receive, set your multi-meter at Rx1 before putting the probes with the terminals of the valve.
  5. If this test confirms that the valve is not in continuity, you’ll need a GE replacement water inlet valve.


The water level switch, also known as a pressure switch & air dome tube

The water level switch, activated by the pressure of water, can be used to regulate the level of the water in the tub. The control panel typically contain this feature. It may also include an air dome tube, or hose which connects to the tub. For GE washers that use electronic controls switch, the switch might be situated in the sump below the tub. The water will fill the tub and compress the air inside, pushing against the diaphragm. The switch controls the valve for water inlet and stop the valve at the correct level of water. How do you check the water level in theGE washer machine:

  1. Because you’ll be working using electrical components, ensure that you have disconnected your appliance prior to starting.
  2. Begin by opening the GE cabinet to the washer. Then, remove the air dome hose. Put the hose in water and then seal the end. After that, blow the other end into the water. If any bubbles rise up to the surface, then you need a new air dome hose.
  3. The switch and the hose should be inspected to see if there is fraying, cracking or wear.
  4. If you suspect that your switch is damaged then you’ll need an GE replacement water switch. A GE washer that is draining simultaneously is frustrating. However, with proper tools and information this issue can be solved.



When you are able to identify the most common reasons for this issue like a blocked drain hose, a faulty water intake valve or an inoperable pressure switch, you’ll be able to get your GE washer back in working quickly. Always check the GE washer’s owner’s manual to find specific guidelines and to disconnect the machine prior to making repairs. You can have your GE washer operating like new with a little patience and understanding.