A Blomber washing machine that stops mid-cycle can be an extremely frustrating and confusing problem to address. It can be frustrating having to start the process over again, and it can also result in costly repairs should the issue continue to persist. But, the causes for a Blomber washing machine not working mid-cycle can easily be addressed by the home owner. In this article, we will examine the common causes that can lead to a washing machine that stops mid-cycle.
We’ll also provide step-by step instructions for fixing the issue. From looking at the door lock to resolving the timer problem, we will cover all that you require to know to resolve the issue. Blomber washing machine to run smoothly once more. So, whether you’re dealing with a Blomber washer that isn’t working or simply looking to save money on repairs, read on to learn how you can fix a Blomber washing machine that stops mid-cycle.
Incoming Power Problem
Be sure the power cord isn’t loose. It must be connected securely to ensure constant electric power to the Blomber washer.
Washing Machine Control Board
Because a Blomber control board for a washing machine is the source of voltage for nearly all of the washer’s electrical components, a damaged board could cause the machine to stop mid-cycle. The board can be inspected for signs of burnt or damaged components. You may also use a multimeter to test the power output connections of the board following a review of the appliance’s wiring diagram.
Washing machine door lock motor and switch assembly
The Blomber door lock locks the door of the washer during operation. The Blomber washer will begin operating when the door has been closed. If the Blomber washer door is not latched shut the door switch blocks the Blomber washer from operating. The machine may stop mid-cycle if the lock fails. Door locks can either fail mechanically or electronically. Examine the door lock for any damages. Replace the door lock if broken or does not latch properly.
Washing Machine Lid Switch Assembly
The lid switch assembly blocks the washer from spinning when the lid is closed. The washer might stop spinning mid-cycle when the lid switch assembly is in a state of deficiency. Multimeters can be used to examine each lid switch to ensure continuity. Replace the lid switch which doesn’t have continuity.
Insufficient water supply
Check that the cold water is running into the tub. The Blomber washer won’t start the rinse cycle if the cold water supply is slow or isn’t reaching the tub. It could be due to an inlet valve that is blocked, a partially closed main valve for water supply, or low pressure water coming from your home.
Washing Machine Water Inlet Valve
While the cycle is running the water inlet valve opens to allow water to enter the wash tub. The washer will wait for water to get in before closing the valve. If the valve malfunctions, it will stop halfway through the cycle. A multimeter can be utilized to verify the continuity of the water inlet valve. Replace the water inlet valve if it does not have continuity. Drain pump for washing machine The Blomber washing-machine drain pump aids in draining the tub of water. It forces the water through a drain tube or pipe that connects to a laundry tub. Since water may be drained from the tub multiple times during a wash, a defective drain pump may stop the washer in mid-cycle. If there’s still water in the tub after the washer has stopped, check the drain pump for any obstruction. Also, you can use a multimeter to test the drain pump to determine if it is in electrical continuity. help determine if the pump is functional or not.
Washing Machine Main Control Board
The control board in the main machine could be defective. But, the control board is not always responsible for this particular symptom. Before replacing the main control board make sure to check the other components that are frequently malfunctioning.
Washing Machine Timer
The timer may be malfunctioning. When diagnosing the timer, prior to replacing the timer, examine all the often defective parts. To find out if the timer’s not working properly, look up the wiring diagram on your washer, and use a multimeter to test the continuity of the timer. An Blomber washing machine which is stopped mid-cycle can be a bit frustrating, however it’s generally a simple solution.
By following the guidelines in this article, you’ll be able troubleshoot and resolve common issues such as clogged filters, malfunctioning door locks, and incorrect timer settings. Make sure you unplug your washer before you attempt any repairs, and if you are unsure about any part of the procedure it is recommended to go through the manual of the manufacturer or call a professional for assistance. With just a some time and patience it is possible to have your Blomber washing machine operating smoothly again, saving you the hassle of having start the process over again and the cost of repairs. Keep an eye on your machine to see whether there are any issues and then take the necessary actions.